Instruments

Tel: +44 (0) 1689 800799
Fax: +44 (0) 1689 800405
info@wallaceinstruments.co.uk

page location: home > products > plasticity > wallace rapid plastimeter p14

Plasticity

Wallace Rapid Plastimeter Mk V- P14

Purpose

The Wallace Rapid Plastimeter measures the plasticity or viscosity of unvulcanised rubbers. The test is simple, clean and quick. The instrument is used in conjunction with the Wallace -MRPRA Ageing Chamber (Cat. Ref. O14) to determine the Plasticity Retention Index (PRI) of raw natural rubbers.

The variable temperature model (P14/VT) characterises the flow behaviour of synthetic rubber compounds as, unlike the other models, its platen temperatures can be varied between 60°C and 180°C. For some applications the P14/VT offers a quick, low cost alternative to a Mooney Viscosity test.

The instrument is supplied in four versions and each version comes complete with specimen cutter. The instrument is shipped with 10mm dia top platen installed and alternative top platens of 7.3 and 14mm diameter are supplied as accessories. The platens are easily interchangeable.

Principle

A modified parallel plate compression principle is used with automatically timed "conditioning" and "load" periods. A sample is compressed between two circular platens which are maintained at a temperature of 100°C. The sample is conditioned for 15 seconds at a thickness of 1mm. A compressive force of 100N is then applied for 15 secs. The final thickness of the test piece expressed in units of 0.01mm, is the plasticity number.

Test Procedure

The sample is prepared using the specimen cutter provided and it is then enclosed between two pieces of tissue paper, as defined by international standards, before being placed between the platens. The tissue paper prevents the material sticking to the platens or sliding between them.

The automatic test sequence is started when the operating handle is rotated.

The reduction in thickness of the sample is displayed digitally, which freezes, to show the plasticity number at the end of 15 sees.

Features

The P14 Rapid Plastimeter offers greatly enhanced operator access and is available in four different versions. A major feature on all versions is powered zero calibration eliminating the need for tedious manual setting. Aluminium castings are used throughout the design for rigidity and stability. All versions comply with National and International standards.

Rapid Plastimeter - Basic Model, P14/1
		Fully automatic operation
		Built in diagnostics
		LED platen Temperature Indicator

Rapid Plastimeter - Printer Model, P14/2
		Compact printer with high speed print capability
		Single/Median mode of operation
		24 Character column print output
		Date and time recorder
		Traceability of aborted tests
		Alternative language settings
		Additional diagnostic features
		Platen Temperature print out

Rapid Plastimeter - Data Terminal and Printer Model, P14/3
		Data input terminal and display
		Compact printer with high speed print capability
		24 Character column print printer
		Date and time recorder
		Continuous Platen temperature display
		Variable load durations
		Sample and operator identification with automatically increasing suffix
		Traceability of aborted tests
		Alternative language settings
		Calibration and service reminder
		PRI evaluation
Rapid Plastimeter - P14/VT
Same specification as the P14/3, plus:
		Variable platen temperature 60°C - 180°C

General

The Plastimeter can be supplied to operate on any normal single phase AC electricity supply.

Three sizes of upper platen anvils are supplied: 7.3 mm, 10 mm and 14 mm diameter. These permit the instrument to operate satisfactorily over a wide plasticity range. The lower platen is suitable for all sizes. Changing the upper platen is a simple operation taking only a few minutes.

Specifications

See the table below for a run-down of this product's specifications.

Plasticity Retention Index (PRI)

PRI is a measure of the resistance of raw natural rubber to oxidation. The oxidation effect is assessed by measuring the plasticity before ageing (P0) and after ageing for 30mins in the Wallace - MRPRA ageing oven at 140°C (P30)